CentOS 7, 최신버전 APM(Apache+PHP+MySQL) 소스설치 및 Openssl 설치하기

 

1. CentOS 7 설치

2 MySQL 소스설치(5.7.13)
3. Openssl 소스설치(1.0.2h)
4. 아파치(Apache) 소스설치(2.4.23)
5. PHP 소스설치(5.6.24)

6. APM+OpenSSL 연동하기

1. CentOS 7 설치과정 중, 기본값인 최소(Minimal Install)로 설치. 시간대, 네트워크 설정, 디스크 선택

 

 

 

2. 네트워크 설정
설치중에 IP Address 정보를 입력해도, ONBOOT=no로 되어 있음. ONBOOT=yes로 수정
[root@localhost network-scripts]# pwd
/etc/sysconfig/network-scripts
[root@localhost network-scripts]# cat ifcfg-eno16777728
TYPE=Ethernet
BOOTPROTO=none
DEFROUTE=yes
IPV4_FAILURE_FATAL=no
IPV6INIT=yes
IPV6_AUTOCONF=yes
IPV6_DEFROUTE=yes
IPV6_FAILURE_FATAL=no
NAME=eno16777728
UUID=45ff82a3-b5b5-411b-a4ca-b6e06a
ONBOOT=yes
HWADDR=00:0C:2...
IPADDR0="IP주소입력"
PREFIX0=24
GATEWAY0="Gateway입력"
DNS1="DNS입력"
IPV6_PEERDNS=yes
IPV6_PEERROUTES=yes

--네트워크 재시작

--CentOS 7 서비스 시작/종료/재시작 방법

--systemctl [start/stop/restart] 서비스명.service​
[root@localhost network-scripts]# systemctl restart NetworkManager
[root@localhost network-scripts]# systemctl restart network

-- hostname 변경

[root@divweb7 ~]# hostnamectl set-hostname divweb7
[root@divweb7 ~]# hostname
divweb7
 

3. 네트워크 명령어-기본값은 ifconfig 없음

1) ip addr 명령어 활용

[root@localhost network-scripts]# ip addr

1: l/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eno1677: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
    valid_lft forever preferred_lft forever

2) net-tools를 설치하면 ifconfig 명령어 사용가능
[root@localhost network-scripts]# yum -y install net-tools

[root@localhost network-scripts]# ifconfig
eno16777728: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 96753  bytes 15370746 (14.6 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 0  (Local Loopback)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

 

[root@localhost ]# cat /etc/selinux/config

# This file controls the state of SELinux on the system.
# SELINUX= can take one of these three values:
#     enforcing - SELinux security policy is enforced.
#     permissive - SELinux prints warnings instead of enforcing.
#     disabled - No SELinux policy is loaded.
#SELINUX=enforcing
SELINUX=disabled
# SELINUXTYPE= can take one of these two values:
#     targeted - Targeted processes are protected,
#     minimum - Modification of targeted policy. Only selected processes are protected.
#     mls - Multi Level Security protection.
SELINUXTYPE=targeted

 

ntsysv 에서 firewall 체크해제

 

 

4.wget, ntsysv 설치

[root@localhost src]#yum -y install gcc* perl* wget*

[root@localhost src]# yum -y install ntsysv*

[root@localhost src]# yum -y install ftp

[root@localhost src]# yum -y install net-snmp
[root@localhost src]# ntsysv